بهینه سازی طراحی بویلرهای HRSG در نیروگاه های سیکل ترکیبی (مقاله علمی وزارت علوم)
درجه علمی: نشریه علمی (وزارت علوم)
آرشیو
چکیده
در نیروگاه های سیکل ترکیبی تولید برق، به جای اینکه گازهای تولید شده از سوزاندن سوخت های فسیلی پس از چرخاندن توربین های گازی به اتمسفر رها شوند، جهت تولید بخار وارد بویلرهای بازیاب می شوند. بخار تولید شده توسط این بویلرها مجددا برای تولید برق در توربین های بخار استفاده می شوند. به این ترتیب راندمان تولید برق به نحو چشمگیری افزایش می یابد. بویلرهای بازیاب با صرف هزینه های زیاد ساخته شده و هرگونه خرابی آن ها موجب توقف بخشی از نیروگاه برق شده و هزینه های سرسام آوری را ایجاد می کنند؛ بنابراین بهینه سازی قابلیت اطمینان آن ها بسیار مهم می باشد. این مقاله به نحوه مدل سازی سیستم تغذیه آب بویلرهای بازیاب (HRSG) با استفاده از ترسیم بلوک دیاگرام قابلیت اطمینان در دو حالت نیمه بار و تمام بار پرداخته و به این وسیله تفاوت دو طرح پیشنهاد شده برای آن ها را از نظر قابلیت اطمینان ارزیابی می کند. روش به کار رفته در این مقاله می تواند در ارزیابی و بهینه یابی قابلیت اطمینان بسیاری از سیستم های صنعتی دیگر نیز به کار رود.Optimization of design of HRSG boilers at cyclic power plants
In combined cycle power plants, instead of releasing gases produced from burning fossil fuels, after turning the gas turbines, they enter into heat recovery steam generator (HRSG) boilers to produce steam. The produced steam by these boilers is used to generate electricity in steam turbines and thus, electricity generation efficiency is dramatically increased. In this way, the efficiency of electricity production increases significantly. These boilers are made at a great cost and also, any failures of them cause a power plant to stop and create enormous costs, so optimizing their reliability is very important. This paper deals with the modeling of the HRSG feed water system by using a block diagram for two states (i.e., half-time and full load), to evaluate the difference between the proposed alternative designs, by considering their reliability. The method used in this paper can be applied to evaluate and optimize the reliability of many other industrial systems. Introduction In power generation, the reliability of industrial control systems is crucial, as failures can disrupt services, leading to accidents and damages. This study focuses on the reliability of Heat Recovery Steam Generator (HRSG) boilers in combined cycle power plants. These plants optimize electricity generation by redirecting gases from burning fossil fuels into heat recovery steam generators. HRSG boiler reliability is pivotal due to high construction costs and the potential for extensive downtime and expenses in case of malfunctions. Addressing this challenge, the research employs the underutilized Reliability Block Diagram (RBD) model, providing a graphical representation of system components and interactions. Specifically tailored to the needs of the Mapna Boiler Company, the study aims to assess and optimize the reliability of the steam production unit, i.e., the boiler, within combined cycle power plants. Research BackgroundReliability, in conjunction with factors such as availability and safety, stands as a cornerstone in ensuring the practical quality of any system. The application of Reliability Block Diagrams (RBD) is a well-established method for modeling and calculating the reliability of industrial systems. Numerous studies have applied RBDs across diverse domains, ranging from power substation automation and wind turbine reliability to error calculations in intelligent submarine power systems. However, despite the versatility of RBDs, a noticeable gap exists in the literature regarding their use for modeling boiler reliability, especially as a multi-state system. Research MethodologyTo undertake a comprehensive reliability analysis of HRSG boilers, the study focuses on distinct subsystems, including:Feed-Water Storage SystemFeed-Water System (FWS)High-Pressure (HP) SectionLow-Pressure (LP) SectionCondensate SystemChemical Dosing System.The Feed-Water System (FWS) is crucial for immediate boiler operation. The initial design involves a Four-Pump System (A2 design) for the FWS. A modification is proposed, removing one feed-water pump, prompting an examination of its impact on boiler reliability. Critical components are identified based on their role in potential disruptions, emphasizing parts causing immediate boiler shutdowns. Using expert knowledge and diagrams, a Reliability Block Diagram (RBD) is developed, visually highlighting weak points. The RBD assesses FWS reliability, comparing two configurations for optimization. Calculation of HRSG Boiler Reliability as a Multistate SystemConfigurations of three-pump and four-pump setups for the Feed-Water System (FWS) are illustrated and analyzed using the Reliability Block Diagram (RBD). The reliability analysis entails a detailed process of data gathering, failure rate determination, and overall reliability calculation for diverse system configurations. The study incorporates probabilities for various operational states and introduces mathematical formulations to calculate the Mean Time Between Failures (MTBF) for water feed system configurations.Fig1: Configuration of HRSG boiler water supply system in 3 pump modeFig2: Configuration of HRSG boiler water supply system in 4 pump mode Steps of optimizing the operational reliability (OPR)Step 1: Identifying Components Used in FWSStep 2: Determining Failure Rates for Each ComponentStep 3: Drawing a Reliability Block Diagram (RBD)Step 4: Evaluating Component ReliabilityStep 5: Calculating Overall Reliability for Each Configuration. ResultsTables present Mean Time Between Failures (MTBF) for water feed system configurations, offering insights into the trade-offs between complete shutdowns and demi-capacity operations. The analysis suggests that the four-pump configuration, while experiencing fewer complete shutdowns, operates at half capacity more frequently compared to the three-pump configuration. The data-driven results highlight the nuances of system reliability and its dynamic nature. Research FindingsThe reliability assessment for boiler construction, considering the failure rates of components over a one-year period, indicates that the four-pump configuration is superior when component reliability is high; otherwise, the three-pump configuration may have an advantage. However, the decision to choose between these configurations necessitates an economic evaluation, accounting for construction costs, shutdown expenses, and half-capacity operation costs. The study underscores the importance of integrating economic considerations with reliability assessments for informed decision-making. Discussion and ConclusionThis research offers valuable insights into vulnerable areas of the HRSG boiler water feeding system, guiding maintenance attention and informing decision-making processes. The study emphasizes the need for future research to consider repair times and incorporate fuzzy reliability values to enhance the robustness of reliability calculations. The holistic approach adopted in this study, combining technical assessments with economic considerations, lays the groundwork for a more comprehensive understanding of system reliability in industrial settings. Suggestions for Future ResearchAs industries evolve, future research should tailor reliability models to specific contexts. Exploring different failure distribution functions beyond the constant-rate assumption opens avenues for investigation. Models like the Weibull mixture model, competitive risk models, compound models, and hybrid models offer promising directions. For instance, the study proposes exploring the application of a compound renewal model, known as complementary risk, for systems with parallel performance and independent components. The limited exploration of this model in the literature presents an opportunity for future research to uncover its potential applications and contributions to reliability modeling.